KPS is open for in person shopping. Masks are required.

Skutt Parts Bands

Sort by:
{"id":6544459628607,"title":"Skutt Lid, Slab and Body Bands for 8 Sided Kilns","handle":"bands_8","description":"pinkwhistlesociety Part Numbers 1000310 – Lid or Slab Band for 8 sided Kilns 1000320 – Body Band for 8 sided Kilns (Specify Top or Bottom) Skutt Part Numbers 0259 – Lid or Slab Band for 8 sided Kilns 0257 – Body Band for 8 sided Kilns (Specify Top or Bottom)\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e","published_at":"2021-03-03T06:30:58-06:00","created_at":"2021-03-03T06:30:59-06:00","vendor":"Skutt","type":"Bands","tags":[],"price":2400,"price_min":2400,"price_max":8100,"available":true,"price_varies":true,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":39254990782527,"title":"Top Lid or Bottom Slab Band \/ New and Old","option1":"Top Lid or Bottom Slab Band","option2":"New and Old","option3":null,"sku":"1000310","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164308031,"product_id":6544459628607,"position":1,"created_at":"2021-11-15T17:05:24-06:00","updated_at":"2021-11-15T17:05:24-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_c0be291d-a459-40a9-8592-3526496b4c56.jpg?v=1637017524","variant_ids":[39254990782527]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 8 Sided Kilns - Top Lid or Bottom Slab Band \/ New and Old","public_title":"Top Lid or Bottom Slab Band \/ New and Old","options":["Top Lid or Bottom Slab Band","New and Old"],"price":2400,"weight":900,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293892671,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_c0be291d-a459-40a9-8592-3526496b4c56.jpg?v=1637017524"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990815295,"title":"Top Section Band \/ New Style Offset Pigtails","option1":"Top Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000320-Top-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164340799,"product_id":6544459628607,"position":2,"created_at":"2021-11-15T17:05:24-06:00","updated_at":"2021-11-15T17:05:24-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0dfd12b2-8da8-4784-92e1-211b0b989f08.gif?v=1637017524","variant_ids":[39254990815295,39254990848063,39254990880831,39254990913599,39254990946367]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 8 Sided Kilns - Top Section Band \/ New Style Offset Pigtails","public_title":"Top Section Band \/ New Style Offset Pigtails","options":["Top Section Band","New Style Offset Pigtails"],"price":7100,"weight":4000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293925439,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0dfd12b2-8da8-4784-92e1-211b0b989f08.gif?v=1637017524"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990848063,"title":"Bottom Section Band \/ New Style Offset Pigtails","option1":"Bottom Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000320-Bottom-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164340799,"product_id":6544459628607,"position":2,"created_at":"2021-11-15T17:05:24-06:00","updated_at":"2021-11-15T17:05:24-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0dfd12b2-8da8-4784-92e1-211b0b989f08.gif?v=1637017524","variant_ids":[39254990815295,39254990848063,39254990880831,39254990913599,39254990946367]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 8 Sided Kilns - Bottom Section Band \/ New Style Offset Pigtails","public_title":"Bottom Section Band \/ New Style Offset Pigtails","options":["Bottom Section Band","New Style Offset Pigtails"],"price":7100,"weight":4000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293925439,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0dfd12b2-8da8-4784-92e1-211b0b989f08.gif?v=1637017524"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990880831,"title":"Top Section Band \/ Old Style Straight Pigtails","option1":"Top Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000320-Top-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164340799,"product_id":6544459628607,"position":2,"created_at":"2021-11-15T17:05:24-06:00","updated_at":"2021-11-15T17:05:24-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0dfd12b2-8da8-4784-92e1-211b0b989f08.gif?v=1637017524","variant_ids":[39254990815295,39254990848063,39254990880831,39254990913599,39254990946367]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 8 Sided Kilns - Top Section Band \/ Old Style Straight Pigtails","public_title":"Top Section Band \/ Old Style Straight Pigtails","options":["Top Section Band","Old Style Straight Pigtails"],"price":7100,"weight":4000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293925439,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0dfd12b2-8da8-4784-92e1-211b0b989f08.gif?v=1637017524"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990913599,"title":"Bottom Section Band \/ Old Style Straight Pigtails","option1":"Bottom Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000320-Bottom-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164340799,"product_id":6544459628607,"position":2,"created_at":"2021-11-15T17:05:24-06:00","updated_at":"2021-11-15T17:05:24-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0dfd12b2-8da8-4784-92e1-211b0b989f08.gif?v=1637017524","variant_ids":[39254990815295,39254990848063,39254990880831,39254990913599,39254990946367]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 8 Sided Kilns - Bottom Section Band \/ Old Style Straight Pigtails","public_title":"Bottom Section Band \/ Old Style Straight Pigtails","options":["Bottom Section Band","Old Style Straight Pigtails"],"price":7100,"weight":4000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293925439,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0dfd12b2-8da8-4784-92e1-211b0b989f08.gif?v=1637017524"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990946367,"title":"Bottom Section 822 ONLY \/ New Style Offset Pigtails","option1":"Bottom Section 822 ONLY","option2":"New Style Offset Pigtails","option3":null,"sku":"1000590-Center","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164340799,"product_id":6544459628607,"position":2,"created_at":"2021-11-15T17:05:24-06:00","updated_at":"2021-11-15T17:05:24-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0dfd12b2-8da8-4784-92e1-211b0b989f08.gif?v=1637017524","variant_ids":[39254990815295,39254990848063,39254990880831,39254990913599,39254990946367]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 8 Sided Kilns - Bottom Section 822 ONLY \/ New Style Offset Pigtails","public_title":"Bottom Section 822 ONLY \/ New Style Offset Pigtails","options":["Bottom Section 822 ONLY","New Style Offset Pigtails"],"price":8100,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293925439,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0dfd12b2-8da8-4784-92e1-211b0b989f08.gif?v=1637017524"}},"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_c0be291d-a459-40a9-8592-3526496b4c56.jpg?v=1637017524","\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0dfd12b2-8da8-4784-92e1-211b0b989f08.gif?v=1637017524"],"featured_image":"\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_c0be291d-a459-40a9-8592-3526496b4c56.jpg?v=1637017524","options":["Band Position","Kiln Pigtail Style"],"media":[{"alt":null,"id":21307293892671,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_c0be291d-a459-40a9-8592-3526496b4c56.jpg?v=1637017524"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_c0be291d-a459-40a9-8592-3526496b4c56.jpg?v=1637017524","width":500},{"alt":null,"id":21307293925439,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0dfd12b2-8da8-4784-92e1-211b0b989f08.gif?v=1637017524"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0dfd12b2-8da8-4784-92e1-211b0b989f08.gif?v=1637017524","width":500}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"pinkwhistlesociety Part Numbers 1000310 – Lid or Slab Band for 8 sided Kilns 1000320 – Body Band for 8 sided Kilns (Specify Top or Bottom) Skutt Part Numbers 0259 – Lid or Slab Band for 8 sided Kilns 0257 – Body Band for 8 sided Kilns (Specify Top or Bottom)\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e"}
Skutt Lid, Slab and Body Bands for 8 Sided Kilns

Skutt Lid, Slab and Body Bands for 8 Sided Kilns

€24.00

pinkwhistlesociety Part Numbers 1000310 – Lid or Slab Band for 8 sided Kilns 1000320 – Body Band for 8 sided Kilns (Specify Top or Bottom) Skutt Part Numbers 0259 – Lid or Slab Band for 8 sided Kilns 0257 – Body Band for 8 sided Kilns (Specify Top or Bottom)There are two types of bands availabel depending on the age of your kiln. Older kilns...


More Info
{"id":6544470835263,"title":"Skutt Blank Ring Band for 1027, 1018, 1027-3, 1018-3, 231, 235","handle":"br_bands_10","description":"KilnParts.com Part Numbers 1000326 – Blank Ring Band for 1027, 1018, 1027-3, 1018-3, 231, 235 Skutt Part Numbers 0158 – Blank Ring Band for 1027, 1018, 1027-3, 1018-3, 231, 235\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e","published_at":"2021-03-03T06:36:32-06:00","created_at":"2021-03-03T06:36:33-06:00","vendor":"Skutt","type":"Bands","tags":[],"price":4000,"price_min":4000,"price_max":4000,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":39255005626431,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"1000326","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Skutt Blank Ring Band for 1027, 1018, 1027-3, 1018-3, 231, 235","public_title":null,"options":["Default Title"],"price":4000,"weight":1816,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158.jpg?v=1637017355"],"featured_image":"\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158.jpg?v=1637017355","options":["Title"],"media":[{"alt":null,"id":21307282161727,"position":1,"preview_image":{"aspect_ratio":1.326,"height":377,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158.jpg?v=1637017355"},"aspect_ratio":1.326,"height":377,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158.jpg?v=1637017355","width":500}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"KilnParts.com Part Numbers 1000326 – Blank Ring Band for 1027, 1018, 1027-3, 1018-3, 231, 235 Skutt Part Numbers 0158 – Blank Ring Band for 1027, 1018, 1027-3, 1018-3, 231, 235\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e"}
Skutt Blank Ring Band for 1027, 1018, 1027-3, 1018-3, 231, 235

Skutt Blank Ring Band for 1027, 1018, 1027-3, 1018-3, 231, 235

€40.00

KilnParts.com Part Numbers 1000326 – Blank Ring Band for 1027, 1018, 1027-3, 1018-3, 231, 235 Skutt Part Numbers 0158 – Blank Ring Band for 1027, 1018, 1027-3, 1018-3, 231, 235There are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need! If th...


More Info
{"id":6544470868031,"title":"Skutt Blank Ring Band for 1227-3, 280","handle":"br_bands_12","description":"KilnParts.com Part Numbers 1000327 – Blank Ring Band for 1227-3, 280 Skutt Part Numbers 0368 – Blank Ring Band for 1227-3, 280\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e","published_at":"2021-03-03T06:36:34-06:00","created_at":"2021-03-03T06:36:34-06:00","vendor":"Skutt","type":"Bands","tags":[],"price":4800,"price_min":4800,"price_max":4800,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":39255005659199,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"1000327","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Skutt Blank Ring Band for 1227-3, 280","public_title":null,"options":["Default Title"],"price":4800,"weight":2270,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158_aca91800-f6db-4eb6-aacf-3ea5b492f019.jpg?v=1637017357"],"featured_image":"\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158_aca91800-f6db-4eb6-aacf-3ea5b492f019.jpg?v=1637017357","options":["Title"],"media":[{"alt":null,"id":21307282227263,"position":1,"preview_image":{"aspect_ratio":1.326,"height":377,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158_aca91800-f6db-4eb6-aacf-3ea5b492f019.jpg?v=1637017357"},"aspect_ratio":1.326,"height":377,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158_aca91800-f6db-4eb6-aacf-3ea5b492f019.jpg?v=1637017357","width":500}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"KilnParts.com Part Numbers 1000327 – Blank Ring Band for 1227-3, 280 Skutt Part Numbers 0368 – Blank Ring Band for 1227-3, 280\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e"}
Skutt Blank Ring Band for 1227-3, 280

Skutt Blank Ring Band for 1227-3, 280

€48.00

KilnParts.com Part Numbers 1000327 – Blank Ring Band for 1227-3, 280 Skutt Part Numbers 0368 – Blank Ring Band for 1227-3, 280There are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need! If the element pigtails inside your kiln control box fo...


More Info
{"id":6544470802495,"title":"Skutt Blank Ring Band for 818, 818-3, 181 or 185","handle":"br_bands_818","description":"KilnParts.com Part Numbers 1000325 – Blank Ring Band for 818, 818-3, 181 or 185 Skutt Part Numbers 0258 – Blank Ring Band for 818, 818-3, 181 or 185\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e","published_at":"2021-03-03T06:36:31-06:00","created_at":"2021-03-03T06:36:31-06:00","vendor":"Skutt","type":"Bands","tags":[],"price":3500,"price_min":3500,"price_max":3500,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":39255005593663,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"1000325","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Skutt Blank Ring Band for 818, 818-3, 181 or 185","public_title":null,"options":["Default Title"],"price":3500,"weight":908,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158_25f6a5c3-559e-4c73-ace3-d623857cbf87.jpg?v=1637017354"],"featured_image":"\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158_25f6a5c3-559e-4c73-ace3-d623857cbf87.jpg?v=1637017354","options":["Title"],"media":[{"alt":null,"id":21307282096191,"position":1,"preview_image":{"aspect_ratio":1.326,"height":377,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158_25f6a5c3-559e-4c73-ace3-d623857cbf87.jpg?v=1637017354"},"aspect_ratio":1.326,"height":377,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158_25f6a5c3-559e-4c73-ace3-d623857cbf87.jpg?v=1637017354","width":500}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"KilnParts.com Part Numbers 1000325 – Blank Ring Band for 818, 818-3, 181 or 185 Skutt Part Numbers 0258 – Blank Ring Band for 818, 818-3, 181 or 185\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e"}
Skutt Blank Ring Band for 818, 818-3, 181 or 185

Skutt Blank Ring Band for 818, 818-3, 181 or 185

€35.00

KilnParts.com Part Numbers 1000325 – Blank Ring Band for 818, 818-3, 181 or 185 Skutt Part Numbers 0258 – Blank Ring Band for 818, 818-3, 181 or 185There are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need! If the element pigtails inside yo...


More Info
{"id":6544470769727,"title":"Skutt Blank Ring Band for 714 or 145","handle":"br_bands_714_145","description":"KilnParts.com Part Numbers 1000324 – Blank Ring Band for 714 or 145 Skutt Part Numbers 0458 – Blank Ring Band for 714 or 145\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e","published_at":"2021-03-03T06:36:30-06:00","created_at":"2021-03-03T06:36:30-06:00","vendor":"Skutt","type":"Bands","tags":[],"price":3400,"price_min":3400,"price_max":3400,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":39255005560895,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"1000324","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Skutt Blank Ring Band for 714 or 145","public_title":null,"options":["Default Title"],"price":3400,"weight":908,"compare_at_price":null,"inventory_management":null,"barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158_20ac009c-3b1b-45af-9143-f8dc64f78ea3.jpg?v=1637017353"],"featured_image":"\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158_20ac009c-3b1b-45af-9143-f8dc64f78ea3.jpg?v=1637017353","options":["Title"],"media":[{"alt":null,"id":21307282030655,"position":1,"preview_image":{"aspect_ratio":1.326,"height":377,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158_20ac009c-3b1b-45af-9143-f8dc64f78ea3.jpg?v=1637017353"},"aspect_ratio":1.326,"height":377,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0158_20ac009c-3b1b-45af-9143-f8dc64f78ea3.jpg?v=1637017353","width":500}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"KilnParts.com Part Numbers 1000324 – Blank Ring Band for 714 or 145 Skutt Part Numbers 0458 – Blank Ring Band for 714 or 145\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e"}
Skutt Blank Ring Band for 714 or 145

Skutt Blank Ring Band for 714 or 145

€34.00

KilnParts.com Part Numbers 1000324 – Blank Ring Band for 714 or 145 Skutt Part Numbers 0458 – Blank Ring Band for 714 or 145There are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need! If the element pigtails inside your kiln control box form...


More Info
{"id":6544459759679,"title":"Skutt Lid, Slab and Body Bands for 609","handle":"bands_609","description":"pinkwhistlesociety Part Numbers 1000313 – Lid or Slab Band for 609 Kiln 1000323 – Body Band for 609 Kiln Skutt Part Numbers 0346 – Lid or Slab Band for 609 Kiln 0347 – Body Band for 609 Kiln\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e","published_at":"2021-03-03T06:31:03-06:00","created_at":"2021-03-03T06:31:04-06:00","vendor":"Skutt","type":"Bands","tags":[],"price":2200,"price_min":2200,"price_max":4900,"available":true,"price_varies":true,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":39254991306815,"title":"Top Lid or Bottom Slab Band \/ New and Old","option1":"Top Lid or Bottom Slab Band","option2":"New and Old","option3":null,"sku":"1000313","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164799551,"product_id":6544459759679,"position":1,"created_at":"2021-11-15T17:05:31-06:00","updated_at":"2021-11-15T17:05:31-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_3dfb1052-6213-4336-84c7-9de9319432f5.jpg?v=1637017531","variant_ids":[39254991306815]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 609 - Top Lid or Bottom Slab Band \/ New and Old","public_title":"Top Lid or Bottom Slab Band \/ New and Old","options":["Top Lid or Bottom Slab Band","New and Old"],"price":2200,"weight":900,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307294384191,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_3dfb1052-6213-4336-84c7-9de9319432f5.jpg?v=1637017531"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254991339583,"title":"Body Section Band \/ New Style Offset Pigtails","option1":"Body Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000323-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164832319,"product_id":6544459759679,"position":2,"created_at":"2021-11-15T17:05:31-06:00","updated_at":"2021-11-15T17:05:31-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_825a82d4-f4a3-46c6-b5b2-dc3ee9dd0de8.gif?v=1637017531","variant_ids":[39254991339583,39254991372351]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 609 - Body Section Band \/ New Style Offset Pigtails","public_title":"Body Section Band \/ New Style Offset Pigtails","options":["Body Section Band","New Style Offset Pigtails"],"price":4900,"weight":4000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307294416959,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_825a82d4-f4a3-46c6-b5b2-dc3ee9dd0de8.gif?v=1637017531"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254991372351,"title":"Body Section Band \/ Old Style Straight Pigtails","option1":"Body Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000323-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164832319,"product_id":6544459759679,"position":2,"created_at":"2021-11-15T17:05:31-06:00","updated_at":"2021-11-15T17:05:31-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_825a82d4-f4a3-46c6-b5b2-dc3ee9dd0de8.gif?v=1637017531","variant_ids":[39254991339583,39254991372351]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 609 - Body Section Band \/ Old Style Straight Pigtails","public_title":"Body Section Band \/ Old Style Straight Pigtails","options":["Body Section Band","Old Style Straight Pigtails"],"price":4900,"weight":4000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307294416959,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_825a82d4-f4a3-46c6-b5b2-dc3ee9dd0de8.gif?v=1637017531"}},"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_3dfb1052-6213-4336-84c7-9de9319432f5.jpg?v=1637017531","\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_825a82d4-f4a3-46c6-b5b2-dc3ee9dd0de8.gif?v=1637017531"],"featured_image":"\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_3dfb1052-6213-4336-84c7-9de9319432f5.jpg?v=1637017531","options":["Band Position","Kiln Pigtail Style"],"media":[{"alt":null,"id":21307294384191,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_3dfb1052-6213-4336-84c7-9de9319432f5.jpg?v=1637017531"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_3dfb1052-6213-4336-84c7-9de9319432f5.jpg?v=1637017531","width":500},{"alt":null,"id":21307294416959,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_825a82d4-f4a3-46c6-b5b2-dc3ee9dd0de8.gif?v=1637017531"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_825a82d4-f4a3-46c6-b5b2-dc3ee9dd0de8.gif?v=1637017531","width":500}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"pinkwhistlesociety Part Numbers 1000313 – Lid or Slab Band for 609 Kiln 1000323 – Body Band for 609 Kiln Skutt Part Numbers 0346 – Lid or Slab Band for 609 Kiln 0347 – Body Band for 609 Kiln\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e"}
Skutt Lid, Slab and Body Bands for 609

Skutt Lid, Slab and Body Bands for 609

€22.00

pinkwhistlesociety Part Numbers 1000313 – Lid or Slab Band for 609 Kiln 1000323 – Body Band for 609 Kiln Skutt Part Numbers 0346 – Lid or Slab Band for 609 Kiln 0347 – Body Band for 609 KilnThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell wh...


More Info
{"id":6544459726911,"title":"Skutt Lid, Slab and Body Bands for 614-3","handle":"bands_614-3","description":"pinkwhistlesociety Part Numbers 1000312 – Lid or Slab Band for 614-3 Kiln 1000322 – Body Band for 614-3 Kiln Skutt Part Numbers 0348 – Lid or Slab Band for 614-3 Kiln 0349 – Body Band for 614-3 Kiln\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e","published_at":"2021-03-03T06:31:01-06:00","created_at":"2021-03-03T06:31:02-06:00","vendor":"Skutt","type":"Bands","tags":[],"price":2200,"price_min":2200,"price_max":7200,"available":true,"price_varies":true,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":39254991208511,"title":"Top Lid or Bottom Slab Band \/ New and Old","option1":"Top Lid or Bottom Slab Band","option2":"New and Old","option3":null,"sku":"1000312","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164602943,"product_id":6544459726911,"position":1,"created_at":"2021-11-15T17:05:29-06:00","updated_at":"2021-11-15T17:05:29-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_357ef7c1-34db-4e3d-b99f-c8f71f4e1dfd.jpg?v=1637017529","variant_ids":[39254991208511]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 614-3 - Top Lid or Bottom Slab Band \/ New and Old","public_title":"Top Lid or Bottom Slab Band \/ New and Old","options":["Top Lid or Bottom Slab Band","New and Old"],"price":2200,"weight":900,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307294187583,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_357ef7c1-34db-4e3d-b99f-c8f71f4e1dfd.jpg?v=1637017529"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254991241279,"title":"Body Section Band \/ New Style Offset Pigtails","option1":"Body Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000322-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164635711,"product_id":6544459726911,"position":2,"created_at":"2021-11-15T17:05:29-06:00","updated_at":"2021-11-15T17:05:29-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_5cd2988a-adf9-4608-a09a-d2376841d09b.gif?v=1637017529","variant_ids":[39254991241279,39254991274047]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 614-3 - Body Section Band \/ New Style Offset Pigtails","public_title":"Body Section Band \/ New Style Offset Pigtails","options":["Body Section Band","New Style Offset Pigtails"],"price":7200,"weight":4000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307294220351,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_5cd2988a-adf9-4608-a09a-d2376841d09b.gif?v=1637017529"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254991274047,"title":"Body Section Band \/ Old Style Straight Pigtails","option1":"Body Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000322-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164635711,"product_id":6544459726911,"position":2,"created_at":"2021-11-15T17:05:29-06:00","updated_at":"2021-11-15T17:05:29-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_5cd2988a-adf9-4608-a09a-d2376841d09b.gif?v=1637017529","variant_ids":[39254991241279,39254991274047]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 614-3 - Body Section Band \/ Old Style Straight Pigtails","public_title":"Body Section Band \/ Old Style Straight Pigtails","options":["Body Section Band","Old Style Straight Pigtails"],"price":7200,"weight":4000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307294220351,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_5cd2988a-adf9-4608-a09a-d2376841d09b.gif?v=1637017529"}},"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_357ef7c1-34db-4e3d-b99f-c8f71f4e1dfd.jpg?v=1637017529","\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_5cd2988a-adf9-4608-a09a-d2376841d09b.gif?v=1637017529"],"featured_image":"\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_357ef7c1-34db-4e3d-b99f-c8f71f4e1dfd.jpg?v=1637017529","options":["Band Position","Kiln Pigtail Style"],"media":[{"alt":null,"id":21307294187583,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_357ef7c1-34db-4e3d-b99f-c8f71f4e1dfd.jpg?v=1637017529"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_357ef7c1-34db-4e3d-b99f-c8f71f4e1dfd.jpg?v=1637017529","width":500},{"alt":null,"id":21307294220351,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_5cd2988a-adf9-4608-a09a-d2376841d09b.gif?v=1637017529"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_5cd2988a-adf9-4608-a09a-d2376841d09b.gif?v=1637017529","width":500}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"pinkwhistlesociety Part Numbers 1000312 – Lid or Slab Band for 614-3 Kiln 1000322 – Body Band for 614-3 Kiln Skutt Part Numbers 0348 – Lid or Slab Band for 614-3 Kiln 0349 – Body Band for 614-3 Kiln\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e"}
Skutt Lid, Slab and Body Bands for 614-3

Skutt Lid, Slab and Body Bands for 614-3

€22.00

pinkwhistlesociety Part Numbers 1000312 – Lid or Slab Band for 614-3 Kiln 1000322 – Body Band for 614-3 Kiln Skutt Part Numbers 0348 – Lid or Slab Band for 614-3 Kiln 0349 – Body Band for 614-3 KilnThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to...


More Info
{"id":6544459661375,"title":"Skutt Lid, Slab and Body Bands for 714","handle":"bands_714","description":"pinkwhistlesociety Part Numbers 1000311 – Lid or Slab Band for 7 sided Kilns 1000321 – Body Band for 7 sided Kilns Skutt Part Numbers 0351 – Lid or Slab Band for 7 sided Kilns 0459 – Body Band for 7 sided Kilns\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e","published_at":"2021-03-03T06:31:00-06:00","created_at":"2021-03-03T06:31:01-06:00","vendor":"Skutt","type":"Bands","tags":[],"price":2300,"price_min":2300,"price_max":7700,"available":true,"price_varies":true,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":39254990979135,"title":"Top Lid or Bottom Slab Band \/ New and Old","option1":"Top Lid or Bottom Slab Band","option2":"New and Old","option3":null,"sku":"1000311","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164504639,"product_id":6544459661375,"position":1,"created_at":"2021-11-15T17:05:27-06:00","updated_at":"2021-11-15T17:05:27-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_c11717cc-3b17-492f-83d5-90ecae622ab4.jpg?v=1637017527","variant_ids":[39254990979135]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 714 - Top Lid or Bottom Slab Band \/ New and Old","public_title":"Top Lid or Bottom Slab Band \/ New and Old","options":["Top Lid or Bottom Slab Band","New and Old"],"price":2300,"weight":900,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307294089279,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_c11717cc-3b17-492f-83d5-90ecae622ab4.jpg?v=1637017527"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254991011903,"title":"Body Section Band \/ New Style Offset Pigtails","option1":"Body Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000321-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164537407,"product_id":6544459661375,"position":2,"created_at":"2021-11-15T17:05:27-06:00","updated_at":"2021-11-15T17:05:27-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0d1ff820-6c4f-4601-b683-4f5fa30fac34.gif?v=1637017527","variant_ids":[39254991011903,39254991044671]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 714 - Body Section Band \/ New Style Offset Pigtails","public_title":"Body Section Band \/ New Style Offset Pigtails","options":["Body Section Band","New Style Offset Pigtails"],"price":7700,"weight":4000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307294122047,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0d1ff820-6c4f-4601-b683-4f5fa30fac34.gif?v=1637017527"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254991044671,"title":"Body Section Band \/ Old Style Straight Pigtails","option1":"Body Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000321-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164537407,"product_id":6544459661375,"position":2,"created_at":"2021-11-15T17:05:27-06:00","updated_at":"2021-11-15T17:05:27-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0d1ff820-6c4f-4601-b683-4f5fa30fac34.gif?v=1637017527","variant_ids":[39254991011903,39254991044671]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 714 - Body Section Band \/ Old Style Straight Pigtails","public_title":"Body Section Band \/ Old Style Straight Pigtails","options":["Body Section Band","Old Style Straight Pigtails"],"price":7700,"weight":4000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307294122047,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0d1ff820-6c4f-4601-b683-4f5fa30fac34.gif?v=1637017527"}},"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_c11717cc-3b17-492f-83d5-90ecae622ab4.jpg?v=1637017527","\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0d1ff820-6c4f-4601-b683-4f5fa30fac34.gif?v=1637017527"],"featured_image":"\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_c11717cc-3b17-492f-83d5-90ecae622ab4.jpg?v=1637017527","options":["Band Position","Kiln Pigtail Style"],"media":[{"alt":null,"id":21307294089279,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_c11717cc-3b17-492f-83d5-90ecae622ab4.jpg?v=1637017527"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_c11717cc-3b17-492f-83d5-90ecae622ab4.jpg?v=1637017527","width":500},{"alt":null,"id":21307294122047,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0d1ff820-6c4f-4601-b683-4f5fa30fac34.gif?v=1637017527"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0d1ff820-6c4f-4601-b683-4f5fa30fac34.gif?v=1637017527","width":500}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"pinkwhistlesociety Part Numbers 1000311 – Lid or Slab Band for 7 sided Kilns 1000321 – Body Band for 7 sided Kilns Skutt Part Numbers 0351 – Lid or Slab Band for 7 sided Kilns 0459 – Body Band for 7 sided Kilns\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e"}
Skutt Lid, Slab and Body Bands for 714

Skutt Lid, Slab and Body Bands for 714

€23.00

pinkwhistlesociety Part Numbers 1000311 – Lid or Slab Band for 7 sided Kilns 1000321 – Body Band for 7 sided Kilns Skutt Part Numbers 0351 – Lid or Slab Band for 7 sided Kilns 0459 – Body Band for 7 sided KilnsThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry ...


More Info
{"id":6544459595839,"title":"Skutt Lid, Slab and Body Bands for 8 Sided 3” Kilns","handle":"bands_8_3","description":"pinkwhistlesociety Part Numbers 1000309 – Lid or Slab Band for 8 sided 3” Kilns 1000319 – Body Band for 8 sided 3” Kilns (Specify Top or Bottom) Skutt Part Numbers 0694 – Lid or Slab Band for 8 sided 3” Kilns 0257 – Body Band for 8 sided 3” Kilns (Specify Top or Bottom)\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e","published_at":"2021-03-03T06:30:56-06:00","created_at":"2021-03-03T06:30:57-06:00","vendor":"Skutt","type":"Bands","tags":[],"price":2400,"price_min":2400,"price_max":8100,"available":true,"price_varies":true,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":39254990585919,"title":"Top Lid or Bottom Slab Band \/ New and Old","option1":"Top Lid or Bottom Slab Band","option2":"New and Old","option3":null,"sku":"1000309","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164111423,"product_id":6544459595839,"position":1,"created_at":"2021-11-15T17:05:22-06:00","updated_at":"2021-11-15T17:05:22-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB.jpg?v=1637017522","variant_ids":[39254990585919]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 8 Sided 3” Kilns - Top Lid or Bottom Slab Band \/ New and Old","public_title":"Top Lid or Bottom Slab Band \/ New and Old","options":["Top Lid or Bottom Slab Band","New and Old"],"price":2400,"weight":900,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293696063,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB.jpg?v=1637017522"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990618687,"title":"Top Section Band \/ New Style Offset Pigtails","option1":"Top Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000319-Top-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164144191,"product_id":6544459595839,"position":2,"created_at":"2021-11-15T17:05:22-06:00","updated_at":"2021-11-15T17:05:22-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_8ad7cbb7-237a-467d-8070-d6b81235bd7b.gif?v=1637017522","variant_ids":[39254990618687,39254990651455,39254990684223,39254990716991,39254990749759]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 8 Sided 3” Kilns - Top Section Band \/ New Style Offset Pigtails","public_title":"Top Section Band \/ New Style Offset Pigtails","options":["Top Section Band","New Style Offset Pigtails"],"price":7100,"weight":4000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293728831,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_8ad7cbb7-237a-467d-8070-d6b81235bd7b.gif?v=1637017522"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990651455,"title":"Bottom Section Band \/ New Style Offset Pigtails","option1":"Bottom Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000319-Bottom-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164144191,"product_id":6544459595839,"position":2,"created_at":"2021-11-15T17:05:22-06:00","updated_at":"2021-11-15T17:05:22-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_8ad7cbb7-237a-467d-8070-d6b81235bd7b.gif?v=1637017522","variant_ids":[39254990618687,39254990651455,39254990684223,39254990716991,39254990749759]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 8 Sided 3” Kilns - Bottom Section Band \/ New Style Offset Pigtails","public_title":"Bottom Section Band \/ New Style Offset Pigtails","options":["Bottom Section Band","New Style Offset Pigtails"],"price":7100,"weight":4000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293728831,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_8ad7cbb7-237a-467d-8070-d6b81235bd7b.gif?v=1637017522"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990684223,"title":"Top Section Band \/ Old Style Straight Pigtails","option1":"Top Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000319-Top-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164144191,"product_id":6544459595839,"position":2,"created_at":"2021-11-15T17:05:22-06:00","updated_at":"2021-11-15T17:05:22-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_8ad7cbb7-237a-467d-8070-d6b81235bd7b.gif?v=1637017522","variant_ids":[39254990618687,39254990651455,39254990684223,39254990716991,39254990749759]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 8 Sided 3” Kilns - Top Section Band \/ Old Style Straight Pigtails","public_title":"Top Section Band \/ Old Style Straight Pigtails","options":["Top Section Band","Old Style Straight Pigtails"],"price":7100,"weight":4000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293728831,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_8ad7cbb7-237a-467d-8070-d6b81235bd7b.gif?v=1637017522"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990716991,"title":"Bottom Section Band \/ Old Style Straight Pigtails","option1":"Bottom Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000319-Bottom-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164144191,"product_id":6544459595839,"position":2,"created_at":"2021-11-15T17:05:22-06:00","updated_at":"2021-11-15T17:05:22-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_8ad7cbb7-237a-467d-8070-d6b81235bd7b.gif?v=1637017522","variant_ids":[39254990618687,39254990651455,39254990684223,39254990716991,39254990749759]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 8 Sided 3” Kilns - Bottom Section Band \/ Old Style Straight Pigtails","public_title":"Bottom Section Band \/ Old Style Straight Pigtails","options":["Bottom Section Band","Old Style Straight Pigtails"],"price":7100,"weight":4000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293728831,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_8ad7cbb7-237a-467d-8070-d6b81235bd7b.gif?v=1637017522"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990749759,"title":"Bottom Section 822-3 ONLY \/ New Style Offset Pigtails","option1":"Bottom Section 822-3 ONLY","option2":"New Style Offset Pigtails","option3":null,"sku":"1000589-Center","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164144191,"product_id":6544459595839,"position":2,"created_at":"2021-11-15T17:05:22-06:00","updated_at":"2021-11-15T17:05:22-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_8ad7cbb7-237a-467d-8070-d6b81235bd7b.gif?v=1637017522","variant_ids":[39254990618687,39254990651455,39254990684223,39254990716991,39254990749759]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 8 Sided 3” Kilns - Bottom Section 822-3 ONLY \/ New Style Offset Pigtails","public_title":"Bottom Section 822-3 ONLY \/ New Style Offset Pigtails","options":["Bottom Section 822-3 ONLY","New Style Offset Pigtails"],"price":8100,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293728831,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_8ad7cbb7-237a-467d-8070-d6b81235bd7b.gif?v=1637017522"}},"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB.jpg?v=1637017522","\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_8ad7cbb7-237a-467d-8070-d6b81235bd7b.gif?v=1637017522"],"featured_image":"\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB.jpg?v=1637017522","options":["Band Position","Kiln Pigtail Style"],"media":[{"alt":null,"id":21307293696063,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB.jpg?v=1637017522"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB.jpg?v=1637017522","width":500},{"alt":null,"id":21307293728831,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_8ad7cbb7-237a-467d-8070-d6b81235bd7b.gif?v=1637017522"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_8ad7cbb7-237a-467d-8070-d6b81235bd7b.gif?v=1637017522","width":500}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"pinkwhistlesociety Part Numbers 1000309 – Lid or Slab Band for 8 sided 3” Kilns 1000319 – Body Band for 8 sided 3” Kilns (Specify Top or Bottom) Skutt Part Numbers 0694 – Lid or Slab Band for 8 sided 3” Kilns 0257 – Body Band for 8 sided 3” Kilns (Specify Top or Bottom)\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e"}
Skutt Lid, Slab and Body Bands for 8 Sided 3” Kilns

Skutt Lid, Slab and Body Bands for 8 Sided 3” Kilns

€24.00

pinkwhistlesociety Part Numbers 1000309 – Lid or Slab Band for 8 sided 3” Kilns 1000319 – Body Band for 8 sided 3” Kilns (Specify Top or Bottom) Skutt Part Numbers 0694 – Lid or Slab Band for 8 sided 3” Kilns 0257 – Body Band for 8 sided 3” Kilns (Specify Top or Bottom)There are two types of bands availabel depending on the age of your kiln....


More Info
{"id":6544459464767,"title":"Skutt Lid, Slab and Body Bands for 10 Sided Kilns","handle":"bands_10","description":"pinkwhistlesociety Part Numbers 1000308 – Lid or Slab Band for 10 sided Kilns 1000318 – Body Band for 10 sided Kilns (Specify Top, Middle or Bottom) Skutt Part Numbers 0159 – Lid or Slab Band for 10 sided Kilns 0157 – Body Band for 10 sided Kilns (Specify Top, Middle or Bottom)\u003cp\u003e\u003c\/p\u003e\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e","published_at":"2021-03-03T06:30:54-06:00","created_at":"2021-03-03T06:30:55-06:00","vendor":"Skutt","type":"Bands","tags":[],"price":2600,"price_min":2600,"price_max":8900,"available":true,"price_varies":true,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":39254990323775,"title":"Top Lid or Bottom Slab Band \/ New and Old","option1":"Top Lid or Bottom Slab Band","option2":"New and Old","option3":null,"sku":"1000308","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164013119,"product_id":6544459464767,"position":1,"created_at":"2021-11-15T17:05:19-06:00","updated_at":"2021-11-15T17:05:19-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_ae8ff0e8-d9ad-402b-8f2a-f086059bc651.jpg?v=1637017519","variant_ids":[39254990323775]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided Kilns - Top Lid or Bottom Slab Band \/ New and Old","public_title":"Top Lid or Bottom Slab Band \/ New and Old","options":["Top Lid or Bottom Slab Band","New and Old"],"price":2600,"weight":1200,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293499455,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_ae8ff0e8-d9ad-402b-8f2a-f086059bc651.jpg?v=1637017519"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990356543,"title":"Top Section Band \/ New Style Offset Pigtails","option1":"Top Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000318-Top-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164045887,"product_id":6544459464767,"position":2,"created_at":"2021-11-15T17:05:19-06:00","updated_at":"2021-11-15T17:05:19-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519","variant_ids":[39254990356543,39254990389311,39254990422079,39254990454847,39254990487615,39254990520383,39254990553151]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided Kilns - Top Section Band \/ New Style Offset Pigtails","public_title":"Top Section Band \/ New Style Offset Pigtails","options":["Top Section Band","New Style Offset Pigtails"],"price":8100,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293532223,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990389311,"title":"Middle Section Band \/ New Style Offset Pigtails","option1":"Middle Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000318-Middle-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164045887,"product_id":6544459464767,"position":2,"created_at":"2021-11-15T17:05:19-06:00","updated_at":"2021-11-15T17:05:19-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519","variant_ids":[39254990356543,39254990389311,39254990422079,39254990454847,39254990487615,39254990520383,39254990553151]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided Kilns - Middle Section Band \/ New Style Offset Pigtails","public_title":"Middle Section Band \/ New Style Offset Pigtails","options":["Middle Section Band","New Style Offset Pigtails"],"price":8100,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293532223,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990422079,"title":"Bottom Section Band \/ New Style Offset Pigtails","option1":"Bottom Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000318-Bottom-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164045887,"product_id":6544459464767,"position":2,"created_at":"2021-11-15T17:05:19-06:00","updated_at":"2021-11-15T17:05:19-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519","variant_ids":[39254990356543,39254990389311,39254990422079,39254990454847,39254990487615,39254990520383,39254990553151]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided Kilns - Bottom Section Band \/ New Style Offset Pigtails","public_title":"Bottom Section Band \/ New Style Offset Pigtails","options":["Bottom Section Band","New Style Offset Pigtails"],"price":8100,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293532223,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990454847,"title":"Top Section Band \/ Old Style Straight Pigtails","option1":"Top Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000318-Top-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164045887,"product_id":6544459464767,"position":2,"created_at":"2021-11-15T17:05:19-06:00","updated_at":"2021-11-15T17:05:19-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519","variant_ids":[39254990356543,39254990389311,39254990422079,39254990454847,39254990487615,39254990520383,39254990553151]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided Kilns - Top Section Band \/ Old Style Straight Pigtails","public_title":"Top Section Band \/ Old Style Straight Pigtails","options":["Top Section Band","Old Style Straight Pigtails"],"price":8100,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293532223,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990487615,"title":"Middle Section Band \/ Old Style Straight Pigtails","option1":"Middle Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000318-Middle-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164045887,"product_id":6544459464767,"position":2,"created_at":"2021-11-15T17:05:19-06:00","updated_at":"2021-11-15T17:05:19-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519","variant_ids":[39254990356543,39254990389311,39254990422079,39254990454847,39254990487615,39254990520383,39254990553151]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided Kilns - Middle Section Band \/ Old Style Straight Pigtails","public_title":"Middle Section Band \/ Old Style Straight Pigtails","options":["Middle Section Band","Old Style Straight Pigtails"],"price":8100,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293532223,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990520383,"title":"Bottom Section Band \/ Old Style Straight Pigtails","option1":"Bottom Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000318-Bottom-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164045887,"product_id":6544459464767,"position":2,"created_at":"2021-11-15T17:05:19-06:00","updated_at":"2021-11-15T17:05:19-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519","variant_ids":[39254990356543,39254990389311,39254990422079,39254990454847,39254990487615,39254990520383,39254990553151]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided Kilns - Bottom Section Band \/ Old Style Straight Pigtails","public_title":"Bottom Section Band \/ Old Style Straight Pigtails","options":["Bottom Section Band","Old Style Straight Pigtails"],"price":8100,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293532223,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990553151,"title":"Middle Section 1022 ONLY \/ New Style Offset Pigtails","option1":"Middle Section 1022 ONLY","option2":"New Style Offset Pigtails","option3":null,"sku":"1000588-Center","requires_shipping":true,"taxable":true,"featured_image":{"id":28886164045887,"product_id":6544459464767,"position":2,"created_at":"2021-11-15T17:05:19-06:00","updated_at":"2021-11-15T17:05:19-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519","variant_ids":[39254990356543,39254990389311,39254990422079,39254990454847,39254990487615,39254990520383,39254990553151]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided Kilns - Middle Section 1022 ONLY \/ New Style Offset Pigtails","public_title":"Middle Section 1022 ONLY \/ New Style Offset Pigtails","options":["Middle Section 1022 ONLY","New Style Offset Pigtails"],"price":8900,"weight":6000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293532223,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519"}},"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_ae8ff0e8-d9ad-402b-8f2a-f086059bc651.jpg?v=1637017519","\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519"],"featured_image":"\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_ae8ff0e8-d9ad-402b-8f2a-f086059bc651.jpg?v=1637017519","options":["Band Position","Kiln Pigtail Style"],"media":[{"alt":null,"id":21307293499455,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_ae8ff0e8-d9ad-402b-8f2a-f086059bc651.jpg?v=1637017519"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_ae8ff0e8-d9ad-402b-8f2a-f086059bc651.jpg?v=1637017519","width":500},{"alt":null,"id":21307293532223,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web.gif?v=1637017519","width":500}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"pinkwhistlesociety Part Numbers 1000308 – Lid or Slab Band for 10 sided Kilns 1000318 – Body Band for 10 sided Kilns (Specify Top, Middle or Bottom) Skutt Part Numbers 0159 – Lid or Slab Band for 10 sided Kilns 0157 – Body Band for 10 sided Kilns (Specify Top, Middle or Bottom)\u003cp\u003e\u003c\/p\u003e\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e"}
Skutt Lid, Slab and Body Bands for 10 Sided Kilns

Skutt Lid, Slab and Body Bands for 10 Sided Kilns

€26.00

pinkwhistlesociety Part Numbers 1000308 – Lid or Slab Band for 10 sided Kilns 1000318 – Body Band for 10 sided Kilns (Specify Top, Middle or Bottom) Skutt Part Numbers 0159 – Lid or Slab Band for 10 sided Kilns 0157 – Body Band for 10 sided Kilns (Specify Top, Middle or Bottom)There are two types of bands availabel depending on the age of yo...


More Info
{"id":6544459300927,"title":"Skutt Lid, Slab and Body Bands for 10 Sided 3” Kilns","handle":"bands_10_3","description":"pinkwhistlesociety Part Numbers 1000307 – Lid or Slab Band for 10 sided 3” Kilns 1000317 – Body Band for 10 sided 3” Kilns (Specify Top, Middle or Bottom) Skutt Part Numbers 0481 – Lid or Slab Band for 10 sided 3” Kilns 0157 – Body Band for 10 sided 3” Kilns (Specify Top, Middle or Bottom)\u003cp\u003e\u003c\/p\u003e\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e","published_at":"2021-03-03T06:30:52-06:00","created_at":"2021-03-03T06:30:53-06:00","vendor":"Skutt","type":"Bands","tags":[],"price":2700,"price_min":2700,"price_max":8900,"available":true,"price_varies":true,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":39254990061631,"title":"Top Lid or Bottom Slab Band \/ New and Old","option1":"Top Lid or Bottom Slab Band","option2":"New and Old","option3":null,"sku":"1000307","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163947583,"product_id":6544459300927,"position":1,"created_at":"2021-11-15T17:05:17-06:00","updated_at":"2021-11-15T17:05:17-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_715d7dd8-333c-479a-b82b-09fcf5c45e0c.jpg?v=1637017517","variant_ids":[39254990061631]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided 3” Kilns - Top Lid or Bottom Slab Band \/ New and Old","public_title":"Top Lid or Bottom Slab Band \/ New and Old","options":["Top Lid or Bottom Slab Band","New and Old"],"price":2700,"weight":1200,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293433919,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_715d7dd8-333c-479a-b82b-09fcf5c45e0c.jpg?v=1637017517"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990094399,"title":"Top Section Band \/ New Style Offset Pigtails","option1":"Top Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000317-Top-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163980351,"product_id":6544459300927,"position":2,"created_at":"2021-11-15T17:05:17-06:00","updated_at":"2021-11-15T17:05:17-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517","variant_ids":[39254990094399,39254990127167,39254990159935,39254990192703,39254990225471,39254990258239,39254990291007]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided 3” Kilns - Top Section Band \/ New Style Offset Pigtails","public_title":"Top Section Band \/ New Style Offset Pigtails","options":["Top Section Band","New Style Offset Pigtails"],"price":8100,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293466687,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990127167,"title":"Middle Section Band \/ New Style Offset Pigtails","option1":"Middle Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000317-Middle-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163980351,"product_id":6544459300927,"position":2,"created_at":"2021-11-15T17:05:17-06:00","updated_at":"2021-11-15T17:05:17-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517","variant_ids":[39254990094399,39254990127167,39254990159935,39254990192703,39254990225471,39254990258239,39254990291007]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided 3” Kilns - Middle Section Band \/ New Style Offset Pigtails","public_title":"Middle Section Band \/ New Style Offset Pigtails","options":["Middle Section Band","New Style Offset Pigtails"],"price":8100,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293466687,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990159935,"title":"Bottom Section Band \/ New Style Offset Pigtails","option1":"Bottom Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000317-Bottom-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163980351,"product_id":6544459300927,"position":2,"created_at":"2021-11-15T17:05:17-06:00","updated_at":"2021-11-15T17:05:17-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517","variant_ids":[39254990094399,39254990127167,39254990159935,39254990192703,39254990225471,39254990258239,39254990291007]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided 3” Kilns - Bottom Section Band \/ New Style Offset Pigtails","public_title":"Bottom Section Band \/ New Style Offset Pigtails","options":["Bottom Section Band","New Style Offset Pigtails"],"price":8100,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293466687,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990192703,"title":"Top Section Band \/ Old Style Straight Pigtails","option1":"Top Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000317-Top-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163980351,"product_id":6544459300927,"position":2,"created_at":"2021-11-15T17:05:17-06:00","updated_at":"2021-11-15T17:05:17-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517","variant_ids":[39254990094399,39254990127167,39254990159935,39254990192703,39254990225471,39254990258239,39254990291007]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided 3” Kilns - Top Section Band \/ Old Style Straight Pigtails","public_title":"Top Section Band \/ Old Style Straight Pigtails","options":["Top Section Band","Old Style Straight Pigtails"],"price":8100,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293466687,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990225471,"title":"Middle Section Band \/ Old Style Straight Pigtails","option1":"Middle Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000317-Middle-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163980351,"product_id":6544459300927,"position":2,"created_at":"2021-11-15T17:05:17-06:00","updated_at":"2021-11-15T17:05:17-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517","variant_ids":[39254990094399,39254990127167,39254990159935,39254990192703,39254990225471,39254990258239,39254990291007]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided 3” Kilns - Middle Section Band \/ Old Style Straight Pigtails","public_title":"Middle Section Band \/ Old Style Straight Pigtails","options":["Middle Section Band","Old Style Straight Pigtails"],"price":8100,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293466687,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990258239,"title":"Bottom Section Band \/ Old Style Straight Pigtails","option1":"Bottom Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000317-Bottom-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163980351,"product_id":6544459300927,"position":2,"created_at":"2021-11-15T17:05:17-06:00","updated_at":"2021-11-15T17:05:17-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517","variant_ids":[39254990094399,39254990127167,39254990159935,39254990192703,39254990225471,39254990258239,39254990291007]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided 3” Kilns - Bottom Section Band \/ Old Style Straight Pigtails","public_title":"Bottom Section Band \/ Old Style Straight Pigtails","options":["Bottom Section Band","Old Style Straight Pigtails"],"price":8100,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293466687,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990291007,"title":"Middle Section 1022-3 ONLY \/ New Style Offset Pigtails","option1":"Middle Section 1022-3 ONLY","option2":"New Style Offset Pigtails","option3":null,"sku":"1000587-Center","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163980351,"product_id":6544459300927,"position":2,"created_at":"2021-11-15T17:05:17-06:00","updated_at":"2021-11-15T17:05:17-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517","variant_ids":[39254990094399,39254990127167,39254990159935,39254990192703,39254990225471,39254990258239,39254990291007]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 10 Sided 3” Kilns - Middle Section 1022-3 ONLY \/ New Style Offset Pigtails","public_title":"Middle Section 1022-3 ONLY \/ New Style Offset Pigtails","options":["Middle Section 1022-3 ONLY","New Style Offset Pigtails"],"price":8900,"weight":6000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293466687,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517"}},"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_715d7dd8-333c-479a-b82b-09fcf5c45e0c.jpg?v=1637017517","\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517"],"featured_image":"\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_715d7dd8-333c-479a-b82b-09fcf5c45e0c.jpg?v=1637017517","options":["Band Position","Kiln Pigtail Style"],"media":[{"alt":null,"id":21307293433919,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_715d7dd8-333c-479a-b82b-09fcf5c45e0c.jpg?v=1637017517"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_715d7dd8-333c-479a-b82b-09fcf5c45e0c.jpg?v=1637017517","width":500},{"alt":null,"id":21307293466687,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_0b106f58-68ec-4c52-8075-b6695defb033.gif?v=1637017517","width":500}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"pinkwhistlesociety Part Numbers 1000307 – Lid or Slab Band for 10 sided 3” Kilns 1000317 – Body Band for 10 sided 3” Kilns (Specify Top, Middle or Bottom) Skutt Part Numbers 0481 – Lid or Slab Band for 10 sided 3” Kilns 0157 – Body Band for 10 sided 3” Kilns (Specify Top, Middle or Bottom)\u003cp\u003e\u003c\/p\u003e\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e"}
Skutt Lid, Slab and Body Bands for 10 Sided 3” Kilns

Skutt Lid, Slab and Body Bands for 10 Sided 3” Kilns

€27.00

pinkwhistlesociety Part Numbers 1000307 – Lid or Slab Band for 10 sided 3” Kilns 1000317 – Body Band for 10 sided 3” Kilns (Specify Top, Middle or Bottom) Skutt Part Numbers 0481 – Lid or Slab Band for 10 sided 3” Kilns 0157 – Body Band for 10 sided 3” Kilns (Specify Top, Middle or Bottom)There are two types of bands availabel depending on t...


More Info
{"id":6544459071551,"title":"Skutt Lid, Slab and Body Bands for 12 Sided Kilns","handle":"bands_12","description":"pinkwhistlesociety Part Numbers 1000306 – Lid or Slab Band for 12 Sided Kilns 1000315 – Body Band for 12 Sided Kilns (Specify Top, Middle or Bottom) 1000316 – Body Band for 1231 Kiln (Center Section Only) Skutt Part Numbers 0376 – Lid or Slab Band for 12 Sided Kilns 0366 – Body Band for 12 Sided Kilns except 1231 Center (Specify Top, Middle or Bottom) 0312 – Body Band for 1231 Kiln (Center Section Only)\u003cp\u003e\u003c\/p\u003e\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e","published_at":"2021-03-03T06:30:49-06:00","created_at":"2021-03-03T06:30:51-06:00","vendor":"Skutt","type":"Bands","tags":[],"price":3100,"price_min":3100,"price_max":9900,"available":true,"price_varies":true,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":39254989766719,"title":"Top Lid or Bottom Slab Band \/ New and Old","option1":"Top Lid or Bottom Slab Band","option2":"New and Old","option3":null,"sku":"1000306","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163882047,"product_id":6544459071551,"position":1,"created_at":"2021-11-15T17:05:15-06:00","updated_at":"2021-11-15T17:05:15-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_966fd357-78bb-4674-8801-179d2c4fa040.jpg?v=1637017515","variant_ids":[39254989766719]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 12 Sided Kilns - Top Lid or Bottom Slab Band \/ New and Old","public_title":"Top Lid or Bottom Slab Band \/ New and Old","options":["Top Lid or Bottom Slab Band","New and Old"],"price":3100,"weight":1200,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293368383,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_966fd357-78bb-4674-8801-179d2c4fa040.jpg?v=1637017515"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254989799487,"title":"Top Section Band \/ New Style Offset Pigtails","option1":"Top Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000315-Top-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163914815,"product_id":6544459071551,"position":2,"created_at":"2021-11-15T17:05:15-06:00","updated_at":"2021-11-15T17:05:15-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515","variant_ids":[39254989799487,39254989832255,39254989865023,39254989897791,39254989930559,39254989963327,39254989996095,39254990028863]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 12 Sided Kilns - Top Section Band \/ New Style Offset Pigtails","public_title":"Top Section Band \/ New Style Offset Pigtails","options":["Top Section Band","New Style Offset Pigtails"],"price":9200,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293401151,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254989832255,"title":"Middle Section Band \/ New Style Offset Pigtails","option1":"Middle Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000315-Middle-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163914815,"product_id":6544459071551,"position":2,"created_at":"2021-11-15T17:05:15-06:00","updated_at":"2021-11-15T17:05:15-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515","variant_ids":[39254989799487,39254989832255,39254989865023,39254989897791,39254989930559,39254989963327,39254989996095,39254990028863]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 12 Sided Kilns - Middle Section Band \/ New Style Offset Pigtails","public_title":"Middle Section Band \/ New Style Offset Pigtails","options":["Middle Section Band","New Style Offset Pigtails"],"price":9200,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293401151,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254989865023,"title":"Bottom Section Band \/ New Style Offset Pigtails","option1":"Bottom Section Band","option2":"New Style Offset Pigtails","option3":null,"sku":"1000315-Bottom-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163914815,"product_id":6544459071551,"position":2,"created_at":"2021-11-15T17:05:15-06:00","updated_at":"2021-11-15T17:05:15-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515","variant_ids":[39254989799487,39254989832255,39254989865023,39254989897791,39254989930559,39254989963327,39254989996095,39254990028863]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 12 Sided Kilns - Bottom Section Band \/ New Style Offset Pigtails","public_title":"Bottom Section Band \/ New Style Offset Pigtails","options":["Bottom Section Band","New Style Offset Pigtails"],"price":9200,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293401151,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254989897791,"title":"Top Section Band \/ Old Style Straight Pigtails","option1":"Top Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000315-Top-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163914815,"product_id":6544459071551,"position":2,"created_at":"2021-11-15T17:05:15-06:00","updated_at":"2021-11-15T17:05:15-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515","variant_ids":[39254989799487,39254989832255,39254989865023,39254989897791,39254989930559,39254989963327,39254989996095,39254990028863]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 12 Sided Kilns - Top Section Band \/ Old Style Straight Pigtails","public_title":"Top Section Band \/ Old Style Straight Pigtails","options":["Top Section Band","Old Style Straight Pigtails"],"price":9200,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293401151,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254989930559,"title":"Middle Section Band \/ Old Style Straight Pigtails","option1":"Middle Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000315-Middle-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163914815,"product_id":6544459071551,"position":2,"created_at":"2021-11-15T17:05:15-06:00","updated_at":"2021-11-15T17:05:15-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515","variant_ids":[39254989799487,39254989832255,39254989865023,39254989897791,39254989930559,39254989963327,39254989996095,39254990028863]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 12 Sided Kilns - Middle Section Band \/ Old Style Straight Pigtails","public_title":"Middle Section Band \/ Old Style Straight Pigtails","options":["Middle Section Band","Old Style Straight Pigtails"],"price":9200,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293401151,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254989963327,"title":"Bottom Section Band \/ Old Style Straight Pigtails","option1":"Bottom Section Band","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000315-Bottom-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163914815,"product_id":6544459071551,"position":2,"created_at":"2021-11-15T17:05:15-06:00","updated_at":"2021-11-15T17:05:15-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515","variant_ids":[39254989799487,39254989832255,39254989865023,39254989897791,39254989930559,39254989963327,39254989996095,39254990028863]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 12 Sided Kilns - Bottom Section Band \/ Old Style Straight Pigtails","public_title":"Bottom Section Band \/ Old Style Straight Pigtails","options":["Bottom Section Band","Old Style Straight Pigtails"],"price":9200,"weight":5000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293401151,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254989996095,"title":"Middle Section 1231 ONLY \/ New Style Offset Pigtails","option1":"Middle Section 1231 ONLY","option2":"New Style Offset Pigtails","option3":null,"sku":"1000316-1231-Center-New","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163914815,"product_id":6544459071551,"position":2,"created_at":"2021-11-15T17:05:15-06:00","updated_at":"2021-11-15T17:05:15-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515","variant_ids":[39254989799487,39254989832255,39254989865023,39254989897791,39254989930559,39254989963327,39254989996095,39254990028863]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 12 Sided Kilns - Middle Section 1231 ONLY \/ New Style Offset Pigtails","public_title":"Middle Section 1231 ONLY \/ New Style Offset Pigtails","options":["Middle Section 1231 ONLY","New Style Offset Pigtails"],"price":9900,"weight":6000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293401151,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254990028863,"title":"Middle Section 1231 ONLY \/ Old Style Straight Pigtails","option1":"Middle Section 1231 ONLY","option2":"Old Style Straight Pigtails","option3":null,"sku":"1000316-1231-Center-Old","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163914815,"product_id":6544459071551,"position":2,"created_at":"2021-11-15T17:05:15-06:00","updated_at":"2021-11-15T17:05:15-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515","variant_ids":[39254989799487,39254989832255,39254989865023,39254989897791,39254989930559,39254989963327,39254989996095,39254990028863]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 12 Sided Kilns - Middle Section 1231 ONLY \/ Old Style Straight Pigtails","public_title":"Middle Section 1231 ONLY \/ Old Style Straight Pigtails","options":["Middle Section 1231 ONLY","Old Style Straight Pigtails"],"price":9900,"weight":6000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293401151,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515"}},"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_966fd357-78bb-4674-8801-179d2c4fa040.jpg?v=1637017515","\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515"],"featured_image":"\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_966fd357-78bb-4674-8801-179d2c4fa040.jpg?v=1637017515","options":["Band Position","Kiln Pigtail Style"],"media":[{"alt":null,"id":21307293368383,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_966fd357-78bb-4674-8801-179d2c4fa040.jpg?v=1637017515"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_966fd357-78bb-4674-8801-179d2c4fa040.jpg?v=1637017515","width":500},{"alt":null,"id":21307293401151,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_d5ee90d2-a10b-4151-8948-ebade88b6001.gif?v=1637017515","width":500}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"pinkwhistlesociety Part Numbers 1000306 – Lid or Slab Band for 12 Sided Kilns 1000315 – Body Band for 12 Sided Kilns (Specify Top, Middle or Bottom) 1000316 – Body Band for 1231 Kiln (Center Section Only) Skutt Part Numbers 0376 – Lid or Slab Band for 12 Sided Kilns 0366 – Body Band for 12 Sided Kilns except 1231 Center (Specify Top, Middle or Bottom) 0312 – Body Band for 1231 Kiln (Center Section Only)\u003cp\u003e\u003c\/p\u003e\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e"}
Skutt Lid, Slab and Body Bands for 12 Sided Kilns

Skutt Lid, Slab and Body Bands for 12 Sided Kilns

€31.00

pinkwhistlesociety Part Numbers 1000306 – Lid or Slab Band for 12 Sided Kilns 1000315 – Body Band for 12 Sided Kilns (Specify Top, Middle or Bottom) 1000316 – Body Band for 1231 Kiln (Center Section Only) Skutt Part Numbers 0376 – Lid or Slab Band for 12 Sided Kilns 0366 – Body Band for 12 Sided Kilns except 1231 Center (Specify Top, Middle ...


More Info
{"id":6544458907711,"title":"Skutt Lid, Slab and Body Bands for 1627","handle":"bands_1627","description":"pinkwhistlesociety Part Numbers 1000305 – Lid or Slab Band for 1627 1000314 – Body Band for 1627 (Specify Top, Middle or Bottom) Skutt Part Numbers 2239 – Lid or Slab Band for 1627 N\/A – Body Band for 1627 (Specify Top, Middle or Bottom)\u003cp\u003e\u003c\/p\u003e\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e","published_at":"2021-03-03T06:30:47-06:00","created_at":"2021-03-03T06:30:49-06:00","vendor":"Skutt","type":"Bands","tags":[],"price":5500,"price_min":5500,"price_max":18500,"available":true,"price_varies":true,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":39254989602879,"title":"Top Lid or Bottom Slab Band","option1":"Top Lid or Bottom Slab Band","option2":null,"option3":null,"sku":"1000305","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163750975,"product_id":6544458907711,"position":1,"created_at":"2021-11-15T17:05:12-06:00","updated_at":"2021-11-15T17:05:12-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_54c3e666-36a3-4d50-a6f7-fb8a3e2e4a08.jpg?v=1637017512","variant_ids":[39254989602879]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 1627 - Top Lid or Bottom Slab Band","public_title":"Top Lid or Bottom Slab Band","options":["Top Lid or Bottom Slab Band"],"price":5500,"weight":1816,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293237311,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_54c3e666-36a3-4d50-a6f7-fb8a3e2e4a08.jpg?v=1637017512"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254989635647,"title":"Top Section Band","option1":"Top Section Band","option2":null,"option3":null,"sku":"1000314-Top","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163783743,"product_id":6544458907711,"position":2,"created_at":"2021-11-15T17:05:12-06:00","updated_at":"2021-11-15T17:05:12-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_b986f04d-c5b6-4da2-9680-df31bf275660.gif?v=1637017512","variant_ids":[39254989635647,39254989668415,39254989701183]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 1627 - Top Section Band","public_title":"Top Section Band","options":["Top Section Band"],"price":18500,"weight":7000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293270079,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_b986f04d-c5b6-4da2-9680-df31bf275660.gif?v=1637017512"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254989668415,"title":"Middle Section Band","option1":"Middle Section Band","option2":null,"option3":null,"sku":"1000314-Middle","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163783743,"product_id":6544458907711,"position":2,"created_at":"2021-11-15T17:05:12-06:00","updated_at":"2021-11-15T17:05:12-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_b986f04d-c5b6-4da2-9680-df31bf275660.gif?v=1637017512","variant_ids":[39254989635647,39254989668415,39254989701183]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 1627 - Middle Section Band","public_title":"Middle Section Band","options":["Middle Section Band"],"price":18500,"weight":7000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293270079,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_b986f04d-c5b6-4da2-9680-df31bf275660.gif?v=1637017512"}},"requires_selling_plan":false,"selling_plan_allocations":[]},{"id":39254989701183,"title":"Bottom Section Band","option1":"Bottom Section Band","option2":null,"option3":null,"sku":"1000314-Bottom","requires_shipping":true,"taxable":true,"featured_image":{"id":28886163783743,"product_id":6544458907711,"position":2,"created_at":"2021-11-15T17:05:12-06:00","updated_at":"2021-11-15T17:05:12-06:00","alt":null,"width":500,"height":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_b986f04d-c5b6-4da2-9680-df31bf275660.gif?v=1637017512","variant_ids":[39254989635647,39254989668415,39254989701183]},"available":true,"name":"Skutt Lid, Slab and Body Bands for 1627 - Bottom Section Band","public_title":"Bottom Section Band","options":["Bottom Section Band"],"price":18500,"weight":7000,"compare_at_price":null,"inventory_management":null,"barcode":null,"featured_media":{"alt":null,"id":21307293270079,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_b986f04d-c5b6-4da2-9680-df31bf275660.gif?v=1637017512"}},"requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_54c3e666-36a3-4d50-a6f7-fb8a3e2e4a08.jpg?v=1637017512","\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_b986f04d-c5b6-4da2-9680-df31bf275660.gif?v=1637017512"],"featured_image":"\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_54c3e666-36a3-4d50-a6f7-fb8a3e2e4a08.jpg?v=1637017512","options":["Band Position"],"media":[{"alt":null,"id":21307293237311,"position":1,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_54c3e666-36a3-4d50-a6f7-fb8a3e2e4a08.jpg?v=1637017512"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0159_WEB_54c3e666-36a3-4d50-a6f7-fb8a3e2e4a08.jpg?v=1637017512","width":500},{"alt":null,"id":21307293270079,"position":2,"preview_image":{"aspect_ratio":1.0,"height":500,"width":500,"src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_b986f04d-c5b6-4da2-9680-df31bf275660.gif?v=1637017512"},"aspect_ratio":1.0,"height":500,"media_type":"image","src":"https:\/\/pinkwhistlesociety.com\/s\/files\/1\/0010\/1931\/4239\/products\/0157_web_b986f04d-c5b6-4da2-9680-df31bf275660.gif?v=1637017512","width":500}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"pinkwhistlesociety Part Numbers 1000305 – Lid or Slab Band for 1627 1000314 – Body Band for 1627 (Specify Top, Middle or Bottom) Skutt Part Numbers 2239 – Lid or Slab Band for 1627 N\/A – Body Band for 1627 (Specify Top, Middle or Bottom)\u003cp\u003e\u003c\/p\u003e\u003cp\u003eThere are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly different band, but don't worry it's easy to tell what you need!\u003c\/p\u003e \u003cp\u003eIf the element pigtails inside your kiln control box form a straight line (bottom band in the image below) your kiln uses the old style band and if the element pigtails are offset you need a new style band (top band in the image below).\u003c\/p\u003e \u003cp\u003e\u003cimg title=\"Skutt New Vs. Old Style Kiln Bands\" src=\"http:\/\/kilnparts.com\/images\/Band\/old_new_band.jpg\" alt=\"Skutt New Vs. Old Style Kiln Bands\" width=\"478\" height=\"273\"\u003e\u003c\/p\u003e \u003cp\u003eIf you need to replace the band on your Skutt electric kiln, don't worry, it's a fairly straightforward process. The bricks are not held in place by any cement, only the tension of the band, so if you need to change a band it's also a good time to chnage any broken bricks. To change a band follow these steps:\u003c\/p\u003e \u003cp\u003e1. Unplug the kiln!\u003c\/p\u003e \u003cp\u003e2. Remove the control box and set it aside. On KM kilns you will need to remove the 4-7 screws (depending on model) from the left side of the control box so the box can swing open. You unplugged and\/or turned off the power to the kiln, right? Remove the female tab connectors from the terminal strip and lift the control box off it's hinges and set it aside. If you have a KS kiln the procdeure is similar, but you will also need to remove the kiln sitter tube from the faceplate by removing the two screws holding it on.\u003c\/p\u003e \u003cp\u003e3. Remove the lid from the kiln and unstack the kiln to gain access to the section you are planning to work on. Place the section on a flat surface. Remember, the bricks are only held in place by the band, so it's important that the section be as flat as possible.\u003c\/p\u003e \u003cp\u003e4. Remove all the hardware from the section including handles, buckels, lid hardware and the heat shield. Save the screws! To remove the heat shield you will need to cut the element connectors so have the correct spare elements ready for your kiln.\u003c\/p\u003e \u003cp\u003e5. Loosen the worm drive screws on the back of the heat shield. Some WD-40 can help with rust. Once the band is loose enough, slide it up and over the section. Be careful, the metal bands have sharp edges. Remember, the brick is now loose.\u003c\/p\u003e \u003cp\u003e6. Put the new section in place being careful to make sure it is oriented correctly. The band should be centered vertically on the bricks. Some small 1\/8\" thich wooden shims can help hold it in place. Start to tighten the worm drive screws. Tighten the worm drive screws evenly from top to bottom. Take a look at the video avilable under the tab \"Product Videos\" for more information on how to tighten the band.\u003c\/p\u003e \u003cp\u003e7. Install the new elements, replace the hardware and restack the kiln.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e\u003cdiv style=\"height: 245px important!; display: block; width: 100%;\"\u003e \u003cp style=\"text-align: center;\"\u003eTightening Skutt Kiln Bands\u003c\/p\u003e \u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/7B6Kj2Y4VCw\" frameborder=\"0\" allowfullscreen\u003e\u003ciframe width=\"400\" height=\"225\" src=\"\/\/www.youtube.com\/embed\/dBSzl9Vjijs\" frameborder=\"0\" allowfullscreen\u003e\u003c\/iframe\u003e\u003c\/iframe\u003e\n\u003c\/div\u003e"}
Skutt Lid, Slab and Body Bands for 1627

Skutt Lid, Slab and Body Bands for 1627

€55.00

pinkwhistlesociety Part Numbers 1000305 – Lid or Slab Band for 1627 1000314 – Body Band for 1627 (Specify Top, Middle or Bottom) Skutt Part Numbers 2239 – Lid or Slab Band for 1627 N/A – Body Band for 1627 (Specify Top, Middle or Bottom)There are two types of bands availabel depending on the age of your kiln. Older kilns use a slightly diffe...


More Info